Properties |
1. Curing ability of thick layer (105⊥ 6h + 120⊥ 4h) .
Not worse than S1, U1 or I4.2
|
2. Volume resistivity
Normal ≡ 1.0℅1012 次﹞m
130⊥ ≡ 1.0℅107次﹞m |
3. Electric strength
Normal ≡ 80MV/m
130⊥ ≡ 40MV/m |
Application |
Suitable for Coils insulation in motors or electric devices |
Fast Curing Melamine Alkyd Impregnating Varnish 1038
Properties |
1. Curing ability of thick layer (105⊥ 6h + 120⊥ 4h) .
Not worse than S1, U1 or I4.2 |
2. Volume resistivity
Normal ≡ 1.0℅1012 次﹞m
130⊥ ≡ 1.0℅107次﹞m |
3. Electric strength
Normal ≡ 80MV/m
130⊥ ≡ 40MV/m |
| Application |
Suitable for Coils insulation in motors or electric devices |
Fast Curing B-F General Polyester Impregnating Varnish 1040-1
Properties |
1. Curing ability of thick layer (120⊥ 10h)
Not worse than S1, U1 or I4.2
|
2. Volume resistivity
Normal ≡ 1.0℅1012 次﹞m
130⊥ ≡ 1.0℅107次﹞m |
3. Electric strength
Normal ≡ 90MV/m
130⊥ ≡ 50MV/m |
Application |
Suitable for Coils insulation in motors or electric devices |
Polyimide Impregnating Varnish 1070
Epoxy Solventless Glue ER-300
Properties |
1. Charpy impact strength
≡ 3.0kJ/m2
2. Volume resistivity
≡ 1.0℅1012次.m
3. Electric strength
≡ 16.0MV/m
4. Dielectric dissipation factor
Tan 汛 ≒ 0.01
5. Relative permittivity
汍 ≒ 4.0 |
Application |
Potting and sealing parts of electric devices |
Epoxy Solventless Trickle Varnish F1133
Properties: F1133 is a type of epoxy solventless trickle varnish modified by unsaturated polyester resin. It is composed of part A and B. Before using the varnish, please fully mix part A and B by the proportion of 1:1 (weight ratio) and wait for about 20 minutes until the bubbles disappeared. It is applied to coils insulation for motors and electric devices of Class B and F. |
Main Technical Data:
Properties |
Test condition / Value |
Outer appearance |
Checked by eye:
Uniformly dissolved, without impurities |
Viscosity (4# cup) |
23⊥㊣2⊥: 15~45s |
Curing time |
130⊥㊣1⊥: 120min. |
Curing of thick layer |
10 grams of sample, 110⊥ 2h + 130⊥ 30min:
Not worse than S1, U1 or I4.2 |
Content of volatile matter |
130⊥㊣1⊥, 2h: ≒15% |
Electric strength |
1ㄘNormal ≡20 MV/m
2ㄘWater immersion 24h ≡18 MV/m |
Volume resistivity |
1ㄘNormal ≡1.0℅1012次﹞m
2ㄘWater immersion 24h ≡1.0℅1010次﹞m |
Bonding strength (Spiral coil method) |
Normal ≡100 N |
| |
| Operation instructions: |
| 1) After well mixing part A and B (usually mixing for 30~60 minutes with a motor), the viscosity of the varnish shall be tested. And then adjust the varnish to meet the requirement of trickling. The life time of the varnish after mixing is 24h. |
| 2) The rotator and stator coils of the motor shall be heated before impregnating. The heating time and temperature are up to the size of the motor. The reference heating time and temperature is: 2 hours at 130⊥ or 10~15 minutes at 190~200⊥. And then do after-treatment for 3~5 hours at 130⊥. |
